Tuesday, 7 August 2012

So you want to start glass fusing....


Whenever I teach a Beginners' Glass Fusing Workshop there is at least one person who decides that glass fusing is the craft for them and they want to do it NOW.
Then they start to consider the costs of setting up a glass fusing studio and the doubt sets in....

OK, so Glass Fusing isn't a hobby you can do at the kitchen table and then clear away for tea. Also, some of the kit is rather expensive (such as a kiln and grinder) and then there's the long process of learning how to operate the kiln, understanding the way glass behaves in high temperatures and being able to put up with more failures than successes at first. But, if you are committed to a love of all things glass, then most problems can be overcome and the final results of creating something both tactile and beautiful make it all worthwhile. 

I learned to fuse glass in a second hand enamelling kiln and all my guidance came from glass fusing websites in the USA. I learned a lot more by joining a glass team on Etsy and I have gained both lots of knowledge and good friends through the Creative Glass Guild of Etsy. But it has been a long, but enjoyable, journey. 

So, what do you need? 



Tools and Equipment
·   Glass cutter – choose an oil filled one such as a Toyo
·   Grozers – ideal for breaking and nibbling glass
·   Cut Running Pliers – for  breaking large pieces of glass
·   Glass Grinder – electric or hand sanding block or     carborundum stone to smooth edges
·   Permanent marker pen – to draw onto glass


Glass Types
·  Float glass – picture or window glass. Molten glass floated on a bed of molten tin to make a smooth, transparent glass. Quite brittle, fuses at 82COE, has a green tinge after firing

·  Bullseye – softer glass with slightly textured surface and, as it is hand rolled, has imperfections in the surface that disappear when fused. Transparent is easier to cut than opal. Fuses at 90COE, is compatible with Uroboros glass

·   Spectrum 96 – cheaper than Bullseye, smaller range of colours and opals are very bright. 96COE

Glass Fusing Basics
 Glass can be cut on thick mdf or a self healing mat
Always handle large sheets with cotton gloves and store upright. Sheet glass held horizontally will increase pressure on centre of the glass and will fracture
When cutting glass take care not to damage the tungsten carbide wheel of the cutter, practice cutting on scrap pieces of float glass
Keep brushing up glass shards as you work   
Check the water level and temperature of the glass grinder before using
Grind all glass from right to left, taking care not to apply pressure to the diamond head
·  Remember to wear goggles when grinding glass
·  Wash all glass component pieces in hot, soapy water, removing all traces of grease and permanent marker pen. Rinse in hot water and dry well


Jo Whitehead
Glassprimitif

Friday, 3 August 2012

Dichroic Glass Workshop

Student work - dichroic coated Bullseye glass
I recently travelled over to York to teach a one day workshop on dichroic coated glass fusing. I loaded up my car and set off to spend a happy Sunday cutting glass in Helen Drye's kitchen. 
Helen is a silver clay jeweller who was looking to expand her designs by including fused dichroic cabochons placed into silver clay settings. Along with her friend Lynne, who is interested in making dichroic glass jewellery, we went through the processes of designing, cutting, grinding and fusing dichroic coated glass. 


Glass heart
Dichroic coated glass is fabulous to work with because, once fused, the most amazing colours come to life and the glass has a colour shift as it catches the light. This means that it gives a touch of luxury to the wearer, enhancing clothing with flashes of colour. As it is a coating of metal oxides onto a glass surface it is also quite expensive to buy. I buy all mine from Warm Glass as they stock CBS (Coatings by Sandberg) dichroic which has the best colours and patterns.



At the workshop both students made three pieces of glass jewellery each, the first using small pieces fused between black and clear Bullseye glass, the second using dichroic coated glass stringers and the third, a design of their own.  I hope the tuition they received has helped them to think about their own designs and come up with their own style. The possibilities are endless. 


I had a lovely day as Helen plied us with tea and lunch in her lovely garden and I hope they enjoyed it too. If you live in North or West Yorkshire and would like to join a glass fusing workshop please email me HERE for details. Follow Glassprimitif on Facebook to see more Students' Work. 

Wednesday, 25 July 2012

Selling My Kiln

AIM kiln 

I have come to realise that, as I now have a larger capacity kiln, my Jeweller's kiln is now surplus to requirements. It's been a fantastic kiln for making small pieces of glass and for firing precious metal clay but I never use it now so I think it needs to go to a good home. 
This is an AIM kiln (measuring 30cm square) with a farenheit temperature gauge (I can supply a conversion chart) and has recently had its elements replaced. The wire elements are in the sides and produce a fairly even temperature throughout the kiln. It does not have a pyrometer, although one can be fitted, but it does have a brand new bung and sits on four sturdy fire brick blocks. It also comes with a kiln shelf measuring 17cm X 16cm and can fuse glass dishes up to 15cm.  This kiln is transportable and will fit on a table in your studio. 


What will it fire? It is the ideal kiln for glass fusing, enamelling, silver clay and glass paints and it fires up to 2000F (1093.333 C) but must not exceed 2381F (1555C).  Voltage is 200 and Amp 7 which means that it will run from an ordinary plug socket. Depending on how frequently it is used, the elements should last up to three years. 


I would like £300 for the kiln (new ones cost from £400+) because I only replaced the heating elements a few months ago. This kiln doesn't come with a guarantee but I recommend Northern Kilns for any future maintenance and I can give the buyer advice on fusing schedules for glass. 
This kiln is in West Yorkshire and I will deliver within a 10 mile radius or buyer can collect. 
Please email Jfwhitehead@blueyonder.co.uk if you are interested. 







Monday, 16 July 2012

Glass Fusing Students

Funky Fish Workshop at South Square Centre

I REALLY enjoyed myself last Saturday teaching a workshop on Funky Fused Glass Fish at South Square Centre. I hope the students did too. Nine future glass artists joined the workshop to learn how to design and create their own fused glass fish in both float and Bullseye glass. The workshop covered the basics of cutting glass, grinding, working with both transparent and opal glass and making some delightful fused glass fish. The workshop also covered colour theory, glass types, how glass behaves in a kiln and fusing and annealing. In fact, a comprehensive introduction into the creative and tech side of  warm glass. Here are the results of the workshop - they did a good job!

Bullseye Glass Fish - students' work 
The next workshop at South Square will be Shards, Frits and Stringers on Saturday 4th August. This is an introduction into making glass tiles or coasters with additional glass pieces, powders and rods. At the end of the workshop I will take the students' glass home and fire it in my kiln before posting it back to them. 


I am now arranging the September workshop on Glass Fusing but I'm in a bit of a quandary regarding what to teach. I have a choice of three workshops so I am asking people to vote HERE. I will teach the workshop that gains the most votes. 
The choices are:
1. Dichroic Glass Jewellery using top quality CBS dichroic coated Bullseye glass to make pendants, earrings, brooches, cufflinks - whatever your fancy. Dichroic glass glitters and shimmers in the light and has an amazing colour shift. 
2. Fused Glass Dishes takes students through the process of designing, cutting and creating fused glass dishes in both float and Bullseye glass (examples HERE) that will then be slumped into moulds to form delightful dishes. 
3. Fused Glass Hangings and Light Catchers with copper wire, inclusions, frit and coloured glass. These look fabulous hung in front of a window (see below). 


Fused Glass Hangings
If you are interested in Glass Fusing Workshops at South Square Centre in Thornton, Bradford please email Glassprimitif or contact South Square HERE. 

Wednesday, 11 July 2012

Art in the Pen - it's official!



Today I received my pack of invites for Art in the Pen and the information for exhibitors so I am both excited and worried.  Excited because I have made all my glass for the event so I won't run low on stock. Worried because I don't have a clue about how to display my glass, even after years of setting up fairs and markets, when it comes to staging design I suck!  

I understand the principles of display such as making sure my display is at different eye levels, grouping in styles and colours, making sure the display materials don't overwhelm the glass, but when it comes to putting this into practice it is a different matter. I have been selecting ideas for display on Pinterest  but I will have to buy some furniture to make this kind of display. 
At least I have the opportunity to go to the Auction Mart next week to measure up my "pen" and make some decisions. If I can get the display right I will feel more confident about booking larger shows and events. Watch this space!